Cutting ceramic with handyman tools

Current images of fusor efforts, components, etc. Try to continuously update from your name, a current photo using edit function. Title post with your name once only. Change image and text as needed. See first posting for details.
Post Reply
User avatar
Rich Feldman
Posts: 1174
Joined: Mon Dec 21, 2009 11:59 pm
Real name: Rich Feldman
Location: Santa Clara County, CA, USA

Cutting ceramic with handyman tools

Post by Rich Feldman » Thu Mar 05, 2015 5:55 pm

At my wife's late parents' house, four brand-new sink faucets didn't fit the 60-year-old sinks. New pop-up drain mechanism expects center hole to be large (1 inch) or set back from mid-line.
DSCN9502.JPG
The chosen remedy was to move the sink holes. Found a Lenox brand diamond-grit hole saw at Lowe's for about $19. New hole intersects old hole, which was taped underneath to hold water.
DSCN9485.JPG
By the third sink I had learned that the drill jig was only needed for starting. The cutter held up well, taking 10-15 minutes per 1/2 inch with a few pounds of force on top of drill motor weight.
DSCN9492.JPG
Sink #4 will wait for a drill extension, instead of getting an angled bore.
DSCN9511.JPG
All models are wrong; some models are useful. -- George Box

User avatar
Andrew Robinson
Moderator
Posts: 686
Joined: Sun Aug 11, 2013 5:54 am
Real name: Andrew Robinson
Location: Raleigh, North Carolina
Contact:

Re: Cutting ceramic with handyman tools

Post by Andrew Robinson » Fri Mar 06, 2015 4:13 am

Interesting, but I'm not sure I understand why you're posting this here? Perhaps documenting your method for others in case they need to cut ceramic for fusor related work?
I can wire anything directly into anything! I'm the professor!

User avatar
Richard Hull
Moderator
Posts: 11731
Joined: Fri Jun 15, 2001 1:44 pm
Real name: Richard Hull

Re: Cutting ceramic with handyman tools

Post by Richard Hull » Fri Mar 06, 2015 6:18 am

I think this post falls under a material science thingy. Lot of folks might need to work finished ceramics. It is good to know there are a number of possible solutions to be found out there at stores like Lowes and Home Depot. This is the sort of image du jour "tip" that will not be archived as noted in the rules. It will have a life span and then go away.

Richard Hull
Progress may have been a good thing once, but it just went on too long. - Yogi Berra
Fusion is the energy of the future....and it always will be
Retired now...Doing only what I want and not what I should...every day is a saturday.

George Dowell
Posts: 158
Joined: Fri May 09, 2003 2:30 pm
Real name:

Re: Cutting ceramic with handyman tools

Post by George Dowell » Mon Mar 09, 2015 7:27 pm

Caveat Emptor drilling electronics related ceramics- often are beryllium oxides- inhalation hazard.

George Dowell

User avatar
Rich Feldman
Posts: 1174
Joined: Mon Dec 21, 2009 11:59 pm
Real name: Rich Feldman
Location: Santa Clara County, CA, USA

Re: Cutting ceramic with handyman tools

Post by Rich Feldman » Fri Mar 20, 2015 7:26 am

Good point about beryllium oxide, George. Toxic when inhaled, excellent electrical insulator, and better thermal conductor than aluminum metal. About 25 years ago my employer used hybrid-circuit substrates made of the stuff.

Maybe one could test ceramics for Be, using alpha particles and a neutron detector. Is the atomic number of Be too low to have a useful XRF spectrum?

I learned that drill extensions with adjustable chucks are hard to come by. Most extensions end with sockets for specific tool sizes. Found none to fit the shank of Lenox hole saw, which is 25/64" round (not 10 mm, though made in UK!) with 3 flats.
So I bought some 3/8" threaded rod and a coupling nut. Drilled the latter out to 25/64 for half its length, and gave it some setscrews.
DSCN9548.JPG
It did the job, but with torque and vibration the rod progressively screwed itself farther into the nut, pushing out the hole saw. Should have taken the time to find a locknut before traveling to job site.

I interrupted the plumbing-fixture installer who had originally discovered the sink problem, and who hardly spoke English, to show him the hole-making technique. 10 minutes later, I saw a well-used 1" Lenox ceramic hole saw in his truck. :oops:
All models are wrong; some models are useful. -- George Box

Post Reply